Floating Pool Cleaner Assembly and Installation

Click here to open the Installation Diagram PDF

Click the image to open the Installation Diagram PDF in a new window

STEP ONE

For the initial assembly of your Dragonfly™ you will first attach the floats.

  1. Attach the floats to the main body with the provided stainless steel bolts and plastic washers. The stainless steel bolts and plastic washers are found screwed into each float. You will need a ½ inch (13mm) wrench.
  2. When inserting the stainless steel bolts through the slots in the main body, ensure that the plastic washers are facing ridge side into slot of the main body.
  3. Set the floats using the marks on the floats to the 4th mark from the top of the float aligning the 4th mark with the top of the weir.
  4. Once the floats are secured in place, ensure that the side valve moves freely up and down.

STEP TWO

Preperation VERY IMPORTANT

  1. Check the pump and filter systems to ensure that both are running at maximum efficiency and are fully primed. Your pool circulation must be functioning at 100%.
  2. Clean the leaf basket or in-line canister.
  3. Clean the cartridge or backwash the DE filter, sand filter or glass filter (your pool has one of the above).
  4. If you have a solar heating system, it must be running efficiently.
  5. Ensure that the hoses to be used are in good condition and are properly connected to the vacuum plate. Flexible, segmented hoses are recommended.

Additional Parts You May Need:

  • Bypass/Diverter Valve
  • Segmented hose lengths to accommodate your pool size.
  • In-line leaf canister for heavy surface debris.
  • 90° Elbow to connect hose into vacuum plate.

STEP THREE

Connecting the hose to the Dragonfly™

  1. Connect the female end of the hose to the male connector at the bottom of your Dragonfly™.
  2. Evacuate as much air as possible from the hose prior to starting the pump.

STEP FOUR

Placing the Dragonfly™ into the pool.

  1. Set your Dragonfly™ upside down in the pool to allow all three floats to fill with water. Ensure there are no air bubbles coming from within the floats – this may be done by rotating the Dragonfly™ under the water at an angle until all of the air is expelled from each of the floats.
  2. While keeping it submerged, carefully turn your Dragonfly™ right side up.
  3. Set the floats so there is approximately ½ inch (13mm) of water over the three weirs. Your Dragonfly™ should now be floating evenly in the water with the three weirs being just below the surface of the water.
  4. Start the pump.

AFTER INSTALLATION

The water should be cascading rhythmically from the surface of the pool over the three weirs and the side valve should open and close intermeittently.

Notes:
  • If the side valve remains open, loosen the bolt, using a ½ inch (13mm) wrench and raise one or more of the floates a little at a time (this causes more water to pass over the weirs) until the side valve starts to open and close.
  • If the side valve remains closed, loosen the bolt, using a ½ inch (13mm) wrench and lower one or more of the floats a little at a time (this causes less water to pass over the weirs) until the side valve starts to open and close.
  • If assembled according to the above Guidelines, your Dragonfly™ is set to work immediately in most situations; however, as there are many differing pump strengths, sometimes an adjustment needs to be made to the floats.

It is rare that your Dragonfly™ floats will need to be readjusted.

If a float has not been correctly fastened or the pump has been renewed, one or more of the floats may need to be adjusted.

It is very important that your pump and filter systems are running at maximum efficiency for the initial Dragonfly™ installation.

The Dragonfly™ is an excellent indicator of when your filtration or other equipment needs attention. Example: Algae or dirt build up in your filter will eventually slow or stop the Dragonfly™ pulsating. The filtration system will require back washing or cleaning. Other causes may be a split or blocked hose.

If after having performed to your satisfaction, you find the operation of your Dragonfly™ changes, please refer to the Customer Care and Troubleshooting Guidelines.

In the interest of safety, before swimming always remove the Dragonfly™ from your pool.

The Dragonfly™ Micro Oil Skimmer


 

The Dragonfly™ Micro Oil Skimmer is a small, self-adjusting emergency oil and scum skimmer. The skimmer's innovative design makes it the most reliable quality skimmer available in its price range.

Contact Us

Toll Free: 1-855-997-4097
Email: info@floatingskimmersusa.com